Home | BimmerBoard on AMAZON | 7 Series E32 Forum | Post New Message | Search | Contact Moderator | Sign In  












Click to make a donation to support BimmerBoard
Follow BimmerBoard
Click to follow us on Twitter Click to follow us on FaceBook Click to follow us on MySpace
Related Links
BMW CCA
Indy Mechanics
E38.org Wiki
David's BMW Bookstore
BimmerBoard on AMAZON
E38.org/e32/
Frappr Map
E32 Lounge
Specialty Forums
Deals & Offers
IBUS Forum
Garage Forum
Navigation A/V
Bluetooth
For Sale
Want To Buy
Off-Topic
Detailing
///M
Kill Stories
Group Buys
Vanos Forum
Meet & Greet
TEST FORUM

Forums for Current Model BMW's
1 Series E81
3 Series E90
5 Series E60
5 Series F10 NEW
6 Series E63/E64
7 Series E65/E66
7 Series F01/02 NEW
X3 E83
X5 E70
X6 E71
Z4 E85
MINI Cooper

Forums for Past Model BMW's
2002
3 Series E21
3 Series E30
3 Series E36
3 Series E46
5 Series E12
5 Series E28
5 Series E34
5 Series E39
6 Series E24
7 Series E23
7 Series E32
7 Series E38
8 Series E31
X5 E53
Z3
Z8 E52
CS E9
Senior Six E3

Model-specific Lounges
E32 Lounge
E36 Lounge
E38 Lounge
E46 Lounge

Regional Forums
Australia
Canada
United Kingdom
Netherlands

Forums for Local BMW Car Clubs
Dallas
Southern California
Minneapolis
Atlanta


Click here to advertise on BimmerBoard.com









Return to the forum index 7 Series E32 Forum

FCPGroton.com

Subject: the wise bcweir tell people what to use, like stabilant 22
Author: shogun (moderator) : member since March, 2004 : 16327 posts
Posted on: 2011-06-09 19:08:35      
Bookmark and Share

stabilant 22A Electrical Contact Enhancer

Model: All BMW
Complaint:
Connectors which carry low current are more likely to form deposits which affect the resistance of the circuit through the plug connector. Depending upon the particular circuit these deposits can cause malfunctions and consequently activate warning lamps and check control indicators.
Remedy:
Part replacement can temporarily stop the problem.
If the connector is the problem then without disconnecting the connector measure the resistance of the circuit running through the connector to make sure the connector has a high resistance. A good resistor will have close to 0 ohms resistance.
Visually examine the male and female terminals in the connector housing by removing them. Look at the integrity of the wire crimps, and in some male terminals the integrity of the weld of the male pin to the terminal. Then reinstall.
With a zero residue electrical contact cleaner liberally spray the male and female connectors, and allow the air to dry.
Apply Stabilant 22A to both male and female terminals so they are saturated, and reconnect the connectors while they are still wet. When the Stabilant 22A dries it will leave a thin coating of polymer film which is conductive between mating surfaces, and is non-conductive between adjacent pins. It can also prevent the formation of more harmful deposits.

E32 750iL 11/88, E32 750iL Highline 03/90
SHOGUN'S TRICKS AND TIPS FOR THE SEVEN SERIES



The 7 Series E32 Forum | Message Thread:


The 7 Series E32 Forum requires users to register before posting new messages.

Click Here to Sign In / Register


Make a donation to support BimmerBoard


Home | Privacy Policy | Terms of Service | Glossary | Advertising

Questions, comments, problems, please email webmaster@bimmerboard.com

©Copyright 2003-2011 BimmerBoard, LLC, All Rights Reserved.
No content from this web site may be reproduced or copied in any
form without the express written consent of BimmerBoard, LLC.


The BMW name and logos are registered trademarks of BMW AG
and BMW of North America, LLC.