Brake caliper and rotor painting project

Click to make a donation to support BimmerBoard

Follow BimmerBoard

Related Links

BMW CCA

Indy Mechanics

E38.org Wiki

David's BMW Bookstore

BimmerBoard on AMAZON

Specialty Forums

Navigation A/V

Bluetooth

For Sale

Want To Buy

Meet & Greet

Forums for Current Model BMW's

Forums for Past Model BMW's

Model-specific Lounges

Regional Forums

Netherlands

Forums for Local BMW Car Clubs

7 Series E23 Forum

This message is marked as Important.

Subject: Brake caliper and rotor painting project
Author: DavidC (moderator) : member since December, 2003 : 12932 posts
Posted on: 2004-06-03 22:13:19

The photos are self explanatory. This turned out to be a nice project.

Items needed:

17mm socket
19mm socket
5mm hex bit
air wrench or socket wrench
hi-temp ceramic paint (silver for the rotors and red for the calipers)
black rust-inhibiting spray paint (Rustoleum satin black)
brake cleaner spray
paper templates and cardboard
masking tape

This is what we started with. Actually, this is the old rotor. I installed new rotors last weekend but decided today that painting them was a good idea. Left unpainted, the new rotors would rust like the old ones pretty quick. In this project, I also cleaned and painted the lower end of the black shock/spring casing with Rustoleum satin black. Be careful not to get any overspray on the shiny metal tube of the shock inside the spring. Paint in that area could cause the seal in your shock to deteriorate.

The paint was purchased at my local AutoZone store. The cost was approximately $4 for each spray can. It didn't make sense to spend $40, or more, on a "special" caliper painting kit. Instead, silver Plasti-Kote hi-temp ceramic engine paint was selected for the rotors along with Red Dupli-color hi-temp ceramic engine paint for the calipers. I would've preferred to use Dupli-color for both, but AutoZone was out of stock for it on the silver. Brakes can get as hot as 800 degrees under hard use. These paints should be able to withstand the heat and the ceramic content should make them durable enough for the brake dust and road debris. Heck, they're recommended for exhaust manifolds so they should be more than adequate for this application.

After removing the rotor from the wheel, it was thoroughly cleaned using brake cleaner spray and paper towels. The gripping surfaces of the rotor were covered with paper and masking tape and the bolt holes were plugged with paper towels. The vent edge and the "hat" of the rotor received two coats of silver paint. Be careful to keep paint off of the gripping surfaces of the rotor. If you get any on them, just wipe it off quickly and clean with a small amount of brake cleaner.

Next, the caliper was cleaned with brake cleaner and the pads and other moving parts were masked off. Every hole, including the bolt holes, was taped or plugged to prevent paint from reaching those areas.

The caliper was suspended on a coat hanger from the shock tower spring. This supports the hydraulic line and provides an easy way to spray the lower end of the caliper assembly without touching anything. Extra towels and cardboard were used to shield the wheel, shock assembly and the rest of the wheel well from overspray.

The red caliper can be easily seen behind the lovely, fashionable TRX wheels. The lug bolts were also spray painted black as well while they were out.

Even at a distance of several feet, the red calipers still grab your attention and look good. If you look closely you can see that the lower end of the shock enclosure, below the spring and above the wheel, has also been painted (Rustoleum satin black) making the whole area look much better than before.

David Cecil
Lexington, KY
Titanium silver '01 750iL, 92k miles
Oxford green '97 740iL, 184k miles
Alpine white '92 750iL, 95k miles (for sale)
Charcoal gray '86 735i, 101k miles (for sale)

Visit e38.org for everything technical about your BMW
Do your Amazon shopping through BimmerBoard on AMAZON and support this forum!

E38 mods: Factory nav retrofit, widescreen display, XM satellite receiver in place of CD changer, custom Valentine1 stealth interface to instrument cluster, BimmerNav bluetooth, factory xenon headlights retrofit, heated seats x4 retrofit, StrongStrut tower brace, crystal clear taillights and corners, M aluminum pedals, stainless steel brake lines, billet aluminum throttle bushings, staggered 18'' M-parallel wheels with Kumho Ecsta LX rubber, quad brake lights conversion

The 7 Series E23 Forum | Message Thread:

Brake caliper and rotor painting project (pic) - DavidC 2004-06-03 22:13:19 (17886 views)
- in pic # 1 are you resting your jack stands on the car's jacking point? - philipuk 2004-06-04 09:34:03 (1388 views)
  - Funny you should mention that. There wasn't room for the jack and (m) - DavidC 2004-06-04 13:13:16 (1281 views)
    - Re: Funny you should mention that. There wasn't room for the jack and (m) - srfsteve 2004-06-04 19:36:22 (1127 views)

This thread is closed to new posts.

Home | Privacy Policy | Terms of Service | Glossary | Advertising

Questions, comments, problems, please email webmaster@bimmerboard.com

©Copyright 2003-2011 BimmerBoard, LLC, All Rights Reserved.
No content from this web site may be reproduced or copied in any
form without the express written consent of BimmerBoard, LLC.

The BMW name and logos are registered trademarks of BMW AG
and BMW of North America, LLC.